SIPLUS F модули ввода дискретных сигналов

General information

Product type designation

F-DI 8x24VDC HF

Firmware version

• ● FW update possible

Yes

based on

6ES7136-6BA01-0CA0

usable BaseUnits

BU type A0

Color code for module-specific color-coded label

CC01

Product function

• ● I&M data

Yes; I&M0 to I&M3

Engineering with

• ● STEP 7 TIA Portal configurable/integrated from version

see entry ID: 109746275

Operating mode

• ● DI

Yes

CiR - Configuration in RUN

Reparameterization possible in RUN

No

Supply voltage

Rated value (DC)

24 V

permissible range, lower limit (DC)

19.2 V

permissible range, upper limit (DC)

28.8 V

Reverse polarity protection

Yes

power supply according to NEC Class 2 required

No

Input current

Current consumption, max.

40 mA; without load

Encoder supply

Number of outputs

8

Short-circuit protection

Yes; Electronic (response threshold 0.7 A to 1.8 A)

Output current

• ● up to 60 °C, max.

0.3 A

24 V encoder supply

• ● 24 V

Yes; min. L+ (-1.5 V)

• ● Short-circuit protection

Yes; Electronic (response threshold 0.7 A to 1.8 A)

• ● Output current per channel, max.

300 mA

• ● Output current per module, max.

800 mA; Total current of all encoders

Power loss

Power loss, typ.

2 W

Address area

Address space per module

• ● Inputs

7 byte; S7-300/400F CPU, 6 byte

• ● Outputs

5 byte; S7-300/400F CPU, 4 byte

Hardware configuration

Automatic encoding

Yes

• ● Electronic coding element type F

Yes

Digital inputs

Number of digital inputs

8

Digital inputs, parameterizable

Yes

Sourcing/sinking input

Yes; P-reading

Input characteristic curve in accordance with IEC 61131, type 1

Yes

Input voltage

• ● Rated value (DC)

24 V

• ● for signal "0"

-30 to +5 V

• ● for signal "1"

+15 to +30 V

Input current

• ● for signal "1", typ.

3.7 mA

Input delay (for rated value of input voltage)

for standard inputs

• — parameterizable

Yes

• — at "0" to "1", min.

0.4 ms

• — at "0" to "1", max.

20 ms

• — at "1" to "0", min.

0.4 ms

• — at "1" to "0", max.

20 ms

for technological functions

• — Parameterizable

No

Cable length

• ● shielded, max.

1 000 m

• ● unshielded, max.

500 m

Interrupts/diagnostics/status information

Diagnostics function

Yes; See Chapter "Alarms/diagnostic messages" in the manual

Alarms

• ● Diagnostic alarm

Yes

• ● Hardware interrupt

No

Diagnostics indication LED

• ● RUN LED

Yes; green LED

• ● ERROR LED

Yes; red LED

• ● Monitoring of the supply voltage (PWR-LED)

Yes; green PWR LED

• ● Channel status display

Yes; green LED

• ● for channel diagnostics

Yes; red LED

• ● for module diagnostics

Yes; green/red DIAG LED

Potential separation

Potential separation channels

• ● between the channels

No

• ● between the channels and backplane bus

Yes

• ● between the channels and the power supply of the electronics

No

Isolation

Isolation tested with

707 V DC (type test)

Standards, approvals, certificates

Suitable for safety functions

Yes

Ecological footprint

• ● environmental product declaration

Yes

Global warming potential

• — global warming potential, (total) [CO2 eq]

52 kg

• — global warming potential, (during production) [CO2 eq]

6.8 kg

• — global warming potential, (during operation) [CO2 eq]

45.8 kg

• — global warming potential, (after end of life cycle) [CO2 eq]

-0.628 kg

Highest safety class achievable in safety mode

• ● Performance level according to ISO 13849-1

PLe

• ● Category according to ISO 13849-1

Cat. 4

• ● SIL acc. to IEC 61508

SIL 3

Probability of failure (for service life of 20 years and repair time of 100 hours)

• — Low demand mode: PFDavg in accordance with SIL3

< 2.00E-05

• — High demand/continuous mode: PFH in accordance with SIL3

< 1.00E-09 1/h

Ambient conditions

Ambient temperature during operation

• ● horizontal installation, min.

-40 °C; = Tmin (incl. condensation/frost)

• ● horizontal installation, max.

60 °C; = Tmax; +70 °C with spacing modules (6AG1193-6BN00-7BA0) or configured slots to the left and right of the module

• ● vertical installation, min.

-40 °C; = Tmin

• ● vertical installation, max.

50 °C; = Tmax

Altitude during operation relating to sea level

• ● Installation altitude above sea level, max.

4 000 m; restrictions for installation altitudes > 2 000 m, see ET 200SP system manual

Relative humidity

• ● With condensation, tested in accordance with IEC 60068-2-38, max.

100 %; RH incl. condensation / frost (no commissioning in bedewed state), horizontal installation

Resistance

Coolants and lubricants

• — Resistant to commercially available coolants and lubricants

Yes; Incl. diesel and oil droplets in the air

Use in stationary industrial systems

• — to biologically active substances according to EN 60721-3-3

Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request

• — to chemically active substances according to EN 60721-3-3

Yes; Class 3C4 (RH < 75 %) incl. salt spray acc. to EN 60068-2-52 (severity degree 3); *

• — to mechanically active substances according to EN 60721-3-3

Yes; Class 3S4 incl. sand, dust, *

• — Against mechanical environmental conditions acc. to EN 60721-3-3

Yes; Class 3M8 using the SIPLUS Mounting Kit ET 200SP (6AG1193-6AA00-0AA0)

Use on ships/at sea

• — to biologically active substances according to EN 60721-3-6

Yes; Class 6B2 mold, fungal and dry rot spores (excluding fauna)

• — to chemically active substances according to EN 60721-3-6

Yes; Class 6C3 (RH < 75 %) incl. salt spray acc. to EN 60068-2-52 (severity degree 3); *

• — to mechanically active substances according to EN 60721-3-6

Yes; Class 6S3 incl. sand, dust; *

• — Against mechanical environmental conditions acc. to EN 60721-3-6

Yes; Class 6M4 using the SIPLUS Mounting Kit ET 200SP (6AG1193-6AA00-0AA0)

Usage in industrial process technology

• — Against chemically active substances acc. to EN 60654-4

Yes; Class 3 (excluding trichlorethylene)

• — Environmental conditions for process, measuring and control systems acc. to ANSI/ISA-71.04

Yes; Level GX group A/B (excluding trichlorethylene; harmful gas concentrations up to the limits of EN 60721-3-3 class 3C4 permissible); level LC3 (salt spray) and level LB3 (oil)

Remark

• — Note regarding classification of environmental conditions acc. to EN 60721, EN 60654-4 and ANSI/ISA-71.04

* The supplied plug covers must remain in place over the unused interfaces during operation!

Conformal coating

• ● Coatings for printed circuit board assemblies acc. to EN 61086

Yes; Class 2 for high reliability

• ● Protection against fouling acc. to EN 60664-3

Yes; Type 1 protection

• ● Military testing according to MIL-I-46058C, Amendment 7

Yes; Discoloration of coating possible during service life

• ● Qualification and Performance of Electrical Insulating Compound for Printed Board Assemblies according to IPC-CC-830A

Yes; Conformal coating, Class A

Dimensions

Width

15 mm

Height

73 mm

Depth

58 mm

Weights

Weight, approx.

29 g